DEVELOPMENT OF (Fe–B–C)-BASED FILLER FOR WEAR-RESISTANT COMPOSITE COATINGS

О. V. Sukhovа, N. O. Zdorovets

Abstract


Purpose. Development of multi-alloyed filler for abrasive wear-resistant composites. Methodology. The methods of microstructural, X-ray and energy-dispersive X-ray analyses were used to achieve research purpose. Micro-mechanical properties of structural constituents and abrasive wear-resistance of composites were determined. Findings. The complete dissolution of chromium and vanadium in the borides of Fe2В and FeВ that are initial structural constituents of Fe–В–С peritectic alloys has been established. These elements primarily dissolve in iron monoboride. Dissolution of molybdenum and niobium is not practically observed. As a result the phases of Мо2В, Мо2(В,С) or NbВ2 can be seen in the structure. Alloying with chromium and vanadium increases compression strength and crack resistance coefficient, but that with molybdenum and niobium enhances total microhardness and hardness of the alloys. Structure formation of the interfaces between the filler and the binder of the composites based on МNМts 20-20 binder is governed by dissolution and diffusion processes when multi-alloyed (Fe–В–С) alloy is applied as filler of the composites. The phase and the structural composition of contact interaction zones canbe explained by re-crystallization of the filler surface layers after dissolution caused by contact with the molten binder. Consequently the macroheterogeneous structure of the composites is free of defects and strong adhesion between the filler and the binder is assured. Contact interaction intensity can be controlled by the choice of temperature-and-time infiltration regimes. Originality. The peculiarities in the formation of structure and properties of Fe2В- and FeВ-based solid solutions observed in the structure of the Fe–В–С peritectic alloys were investigated that allowed us to recommend composition of multicomponent alloy to be applied as filler of (Cu–Ni–Mn)-matrix macroheterogeneous composites. Practical value. Owing to multiple alloying of the filler based on Fe–В–С peritectic alloy with chromium, vanadium, molybdenum and niobium the abrasive wear resistance of composite coatings can be compared with that of tungsten-containing coatings, which ensures saving of expensive and deficient materials.

Keywords


Fe–B–C peritectic alloys; alloying; mechanical properties; composite; filler

References


Abuzin Yu.А. Funktsionalnyye metallicheskiye kompozitsionnyye materialy i tekhnologii v mashistroyenii [Functional metallic composites and technologies in mechanical engineering]. Materialy v mashistroyenii – Materials in mechanical engineering, 2010, no. 6, pp. 52-54.

Belousov V.Ya. Dolgovechnost detaley mashin s kompozitsionnymi materialami [Service life of machine parts with composites]. Lviv, Vyshcha shkola Publ., 1984. 180 p.

Danilov L.I., Rovenskikh F.M. Naplavka detaley zasypnykh ustroystv domennykh pechey kompozitsionnym splavom [Facing of charging devices parts of blast furnaces by composite alloy]. MetallurgMetallurgist, 1979, no. 1, pp. 12-15.

Myshko Yu.D. Naplavka filyer kompozitsionnymi splavami [Facing of drawing dies by composite alloys]. Khimicheskoye i neftyanoye mashinostroyeniyeChemical and oil mechanical engineering, 1983, no. 6, pp. 28-30.

Spiridonova I.М., Panasyuk A.D., Sukhovaya Ye.V., Umanskiy A.P. Stabilnost kompozitsionnykh materialov [Composites stability]. Dnipropetrovsk, Svidler Publ., 2011. 244 p.

Sukhovaya Ye.V., Syrovatko Yu.V. Kvantovomekhnicheskaya model formirovaniya zon kontaktnogo vzaimodeistviya v kompozitsionnykh materialakh so sfericheskim napolnitelem [Quantum-mechanical model of contact interaction zones formation of composites strengthened with spherical filler]. Visnyk Dnipropetrov-skoho natsionalnoho universytetu zaliznychnoho transportu imeni akademika V. Lazariana [Bulletin of Dnipropetrovsk National University of Railway Transport named after Academician V. Lazaryan], 2011, issue 37, pp. 238-243.

Sukhovaya Ye.V., Syrovatko Yu.V. Vliyaniye P i Mo na formirovaniye granits razdela v kompozitsionnykh materialakh [Influence of P and Mo on interface formation of (Fe-В-С)-based composites]. Visnyk Dnipropetrovskoho natsionalnoho universytetu zaliznychnoho transportu imeni akademika V. Lazariana [Bulletin of Dnipropetrovsk National University of Railway Transport named after Academician V. Lazaryan], 2010, issue 34, pp. 219-225.

Yuzvenko Yu.А., Frumin Ye.I., Pashchenko M.A. Sfericheskiy relit. Sposob polucheniya i svoystva [Spherical relit. Fabrication method and properties]. Poroshkovaya metallurgiya – Powder metallurgy, 1975, no. 7, pp. 1-5.

Berns H., Fischer A. Microstructure of Fe–Cr–C hardfacing alloys with additions of Nb, Ti, and B. Metallography, 1987, vol. 20, pp. 401-429. doi: 10.1016/0026-0800(87)90017-6.

Callister Jr.W.D. Materials Science and Engineering: An Introduction. New York, John Wiley & Sons, Inc. Publ., 2003. 867 p. doi: 10.1108/acmm.2000.12847aae.001.

Mukhopadhyay N.K., Murthy G.V.S., Weatherly B.S. Alloys Compounds. Singapore, World Scientific Publ., 2002. 206 p.

Carreno-Morelli E., Cutard T., Schaller R., Bonjour C. Processing and characterization of aluminum-based metal matrix composites produced by gas pressure infiltration. Materials Science and Engineering, 1998, no. А 251, pp. 48-57. doi: 10.1016/S0921-5093(98)00649-2.

Sukhova O.V., Spyrydonova I.M. Corrosion-resistant Fe–B–C alloys. Visnyk Dnipropetrovskoho universytetu. Fizyka. Radioelectronika [Bulletin ofDnipropetrovskUniversity. Physics. Radio Electronics], 2011, vol. 19, no. 2, pp. 62-65.

Sukhova O. V., Spyrydonova I. M. High performance composites. Visnyk Dnipropetrovskoho universytetu. Fizyka. Radioelectronika [Bulletin of Dnipropetrovsk University. Physics. Radio Electronics], 2012, vol. 20, no. 2, pp. 78-81.


GOST Style Citations


1. Абузин, Ю. А. Функциональные металлические композиционные материалы и технологии в ма-шиностроении / Ю. А. Абузин // Материалы в машиностроении. – 2010. – № 6. – C. 52–54.


2. Белоусов, В. Я. Долговечность деталей машин с композиционными материалами / В. Я. Белоусов. – Львів : Вищ. шк., 1984. – 180 с.


3. Данилов, Л. И. Наплавка деталей засыпных устройств доменных печей композиционным сплавом / Л. И. Данилов, Ф. М. Ровенских // Металлург. – 1979. – № 1. – С. 12–15.


4. Мышко, Ю. Д. Наплавка фильер композиционными сплавами / Ю. Д. Мышко, В. Г. Нечипоренко, А. Н. Гладченко // Хим. и нефтяное машиностроение. – 1983. – № 6. – С. 28–30.


5. Стабильность композиционных материалов / И. М. Спиридонова, А. Д. Панасюк, Е. В. Суховая, А. П. Уманский. – Днепропетровск : Свидлер, 2011. – 244 с.


6. Суховая, Е. В. Квантовомеханическая модель формирования зон контактного взаимодействия в композиционных материалах со сферическим наполнителем / Е. В. Суховая, Ю. В. Сыроватко // Вісн. Дніпропетр. нац. ун-ту залізн. трансп. ім. акад. В. Лазаряна. – Дніпропет-ровськ, 2011. – Вип. 37. – С. 238–243.


7. Суховая, Е. В. Влияние Р и Мо на формирование границ раздела в композиционных материалах со связкой Fe-В-С / Е. В. Суховая, Ю. В. Сыроватко // Вісн. Дніпропетр. нац. ун-ту залізн. трансп. ім. акад. В. Лазаряна. – Дні-пропетровськ, 2010. – Вип. 34. – С. 219–225.

8. Юзвенко, Ю. А. Сферический релит. Способ получения и свойства / Ю. А. Юзвенко, Е. И. Фрумин, М. А. Пащенко // Порошковая металлургия. – 1975. – № 7. – С. 1–5.


9. Berns, H. Microstructure of Fe–Cr–C hardfacing alloys with additions of Nb, Ti, and B / H. Berns, A. Fischer // Metallography. – 1987. – Vol. 20. – P. 401–429. doi: 10.1016/0026-0800(87)90017-6.


10. Callister, Jr. W. D. Materials Science and Engineering: An Introduction / Jr. W. D. Callister. – New York: John Wiley & Sons Inc., 2003. – 867 p. doi: 10.1108/acmm.2000.12847aae.001.

11. Mukhopadhyay, N. K. Alloys Compounds / N. K. Mukhopadhyay, G. V. S. Murthy, B. S. Wea-therly. –Singapore : World Scientific, 2002. – 206 p.


12. Processing and characterization of aluminum-based metal matrix composites produced by gas pressure infiltration / E. Carreno-Morelli, T. Cutard, R. Schaller, C. Bonjour // Materials science and engineering. – 1998. – № А 251. – P. 48–57. doi: 10.1016/S0921-5093(98)00649-2.


13. Sukhova, O. V. Corrosion-resistant Fe–B–C alloys / O. V. Sukhova, I. M. Spyrydonova // Вісн. ДУ. Фізика. Радіоелектроніка. – 2011. – Т. 19, № 2. – С. 62–65.


14. Sukhova, O. V. High performance composites / O. V. Sukhova, I. M. Spyrydonova // Вісн. ДУ. Фізика. Радіоелектроніка. – 2012. – Т. 20, № 2. – С. 78–81.



DOI: https://doi.org/10.15802/stp2014/33396

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

 

ISSN 2307–3489 (Print)
ІSSN 2307–6666 (Online)