COMPARATIVE ANALYSIS OF COMPLEX MECHANICAL PROPERTIES OBTAINED IN TESTS ON FINISHED BOLTS AND TURNED SAMPLES

Authors

DOI:

https://doi.org/10.15802/stp2015/50121

Keywords:

high-strength bolts, ready to bolt, planed samples, tensile test, mechanical properties, incision

Abstract

Purpose. The purpose of the work is provided by the system experimental study of the effect of strengthening the level of the ratio of complex mechanical properties of the finished bolts and peeled samples and analysis of the data on the basis of geometric and structural reinforcement. Methodology. A uniaxial tensile test was carried out on full-size bolts and the peeled samples to diameters of 10 mm and 8 mm at a testing machine FP - 100/1 recording full diagram of deformation and fracture. Findings. The level of strength of qualitatively and quantitatively has different effects on the characteristics of the ratio of resistance to plastic deformation and ductility characteristics ductile fracture resistance, determined on the finished bolts and peeled samples. At the same time, the analysis suggests that the combination of mechanical properties determined on finished bolts, the most adequate to their mechanical behavior during operation. This conclusion is particularly important for acceptance testing of bolts of strength class 8.8 or higher. Originality. For the first time experimentally shown that the system is functional cuts on specific metal products can have both hardening and softening effect on the characteristics of resistance to plastic deformation in terms of normal stress depending on the level of hardening and given an interpretation of the observed phenomena on the basis of changes in the ratio of the concentration of eg-tions and the degree of rigidity of the stress state in the cuts. Practical value. Limitation of mechanical tests are only willing bolts, other than greater consistency determines the properties of their structural strength bolts in the operation, reduce the overall time-consuming tests.

Author Biographies

Y. P. Gul, National Metallurgical Academy of Ukraine

Dep. «Metal Heat Treatment», Gagarin Av., 4, Dnipropetrovsk, Ukraine, 49600, tel. +38 (0562) 46 24 53

A. V. Ivchenko, National Metallurgical Academy of Ukraine

Dep. «Metal Heat Treatment», Gagarin Av., 4, Dnipropetrovsk, Ukraine, 49600, tel. +38 (0562) 46 24 53

P. V. Kondratenko, National Metallurgical Academy of Ukraine

Dep. «Metal Heat Treatment», Gagarin Av., 4, Dnipropetrovsk, Ukraine, 49600, tel. +38 (0562) 46 24 53

G. I. Perchun, National Metallurgical Academy of Ukraine

Dep. «Metal Heat Treatment», Gagarin Av., 4, Dnipropetrovsk, Ukraine, 49600, tel. +38 (0562) 46 24 53

References

Voynov K.N. Resheniye tribologicheskikh problem transporta [The solution of tribological problems of transport]. Transport Rossiyskoy Federatsii –Transport of Russian Federation, 2009, no. 2, pp. 60-63.

Ivchenko A.V., Gul Yu.P. Sovershenstvovaniye standartov i metodov ispytaniya armaturnogo prokata na rastyazheniye [The improvement of standards and test methods for reinforcing bars in tension]. Metallurgicheskaya i gornorudnaya promyshlennost – Metallurgical and Mining Industry, 2014, no. 6, pp. 125-128.

Klyuchnik S.V. Epokha novykh tekhnologiy na sluzhbe u mostovykh konstruktsiy [Era of new technologies for bridges constructions]. Visnyk Dnipropetrovskoho natsionalnoho universytetu zaliznychnoho transportu imeni akademika V. Lazariana [Bulletin of Dnipropetrovsk National University of Railway Transport named after Academician V. Lazaryan], 2010, issue 33, pp. 111-113.

Matlin M.M., Manukyan D.S. Issledovaniye vliyaniya kontsentratorov napryazheniya na prochnost boltovykh soedineniy [Study of the stress concentrations effect on the strength of bolted connections]. Sbornik nauchnykh trudov SWorld [Proc. of SWorld].Odessa, SWorld Publ., 2012, pp. 423-427.

Moyseyenko K.V. Vliyaniye dliny pryamoy vstavki na dopustimyye skorosti dvizheniya poyezdov smezhnymi strelochnymi perevodami, ulozhennymi po pervoy skheme [Fathom influence of straight insertion on allowed speed by allied pointworks which are created by the first scheme]. Visnyk Dnipropetrovskoho natsionalnoho universytetu zaliznychnoho transportu imeni akademika V. Lazariana [Bulletin of Dnipropetrovsk National University of Railway Transport named after Academician V. Lazaryan], 2011, issue 38, pp. 117-126.

Peterson R. Koeffitsienty kontsentratsii napryazheniy [The coefficients of stress concentration].Moscow, Mir Publ., 1977. 300 p.

Rogovskiy A.G., Shepeleva F.A. Mekhanicheskiye svoystva boltov iz legirovannoy stali [Mechanical properties of alloy steel bolts]. Metiznoye proizvodstvo – Hardware Production, 1974, issue 4, pp. 100-113.

Tarkhanov V.I., Sadriev Z.M. Statisticheskaya i ustalostnaya prochnost rezbovykh soyedineniy [Statistical and fatigue strength of threaded connections]. Sbornik nauchnykh trudov V Mezhdunarodnoy nauchno-tekhnicheskoy konferentsii (15.10.–16.10. 2009) [Proc. of V Intern. Scientific and Technical Conf.]. Ulyanovsk, 2009, pp. 132-134.

Vakulenko I.A., Bolshakov V.I. Morfologiya struktury i deformatsionnoye uprochneniye stali [The morphology of the structure and work hardening of steel]. Dnepropetrovsk, Makovetskiy Publ., 2008. 196 p.

Bickford J.H. Introduction to the Design and Behavior of Bolted Joints.London,Taylor& Francis Group Publ., 2013. 564 p.

Pedersen N.L. Optimization of Bolt Stress. 10th World Congress on Structural and Multidisciplinary Optimization (19.05.–24.05.2013), 2013, pp. 142-148.

Walter D. Peterson’s stress concentration factors.New Jersey, John Wiley & Sons, Inc. Publ., 2008. 555 p.

Gul Yu.P. Osnovnyye printsipy i praktika geometricheski-strukturnogo uprochneniya metalloizdeliy [Basic principles and practice of geometric and structural hardening of metal]. Stal – Steel, 2012, no. 8, pp. 40-45.

Gul Yu.P., Ivchenko A.V., Ambrazhey M.Yu. Otsenka konstruktivnoy prochnosti vysokoprochnykh boltov na osnove rezultatov sdatochnykh ispytaniy [Evaluation of the structural strength of high-strength bolts based on the results of delivery trials]. StalSteel, 2011, no. 9, pp. 42-46.

Petrikov V.G., Vlasov A.P. Progressivnyye krepezhnyye izdeliya [Progressive fasteners].Moscow, Mashinostroeniye Publ., 1991. 256 p.

Published

2015-09-14

How to Cite

Gul, Y. P., Ivchenko, A. V., Kondratenko, P. V., & Perchun, G. I. (2015). COMPARATIVE ANALYSIS OF COMPLEX MECHANICAL PROPERTIES OBTAINED IN TESTS ON FINISHED BOLTS AND TURNED SAMPLES. Science and Transport Progress, (4(58), 132–141. https://doi.org/10.15802/stp2015/50121

Issue

Section

MATERIAL SCIENCE