REDUCTION IN CUTS SPEED AT THE BEGINNING OF A SORTING SIDINGS, EQUIPPED WITH QUASI-CONTINUOUS SPEED CONTROL SYSTEM
DOI:
https://doi.org/10.15802/stp2016/77881Keywords:
hump, sorting siding, slope of siding, cut, point car retarders, brake position, quasi-continuous speed control systemAbstract
Purpose. Clear and uninterrupted operation of humps depends on the quality of technical equipment and control technology of cuts speed. Technology of interval and purposive regulation of cuts speed is used at most humps. The article discusses ways to reduce the cuts rolling speed to a safe level at the beginning of the sorting sidings equipped with quasi-continuous speed control system. Methodology. It proposed three fundamentally different ways to reduce the cuts rolling speed at the beginning of the sorting siding. The analysis of the ways to reduce cuts rolling speed to a safe level at the beginning of the sorting sidings was conducted using simulation the process of cuts rolling from humps equipped with quasi-continuous speed control. Findings. As a result of analysis, the inappropriateness of opposite elevation using on the roll-out part of the hump after the last separation switch point. Spot regulators of cars speed can be used to reduce the cuts rolling speed at the beginning of the sorting siding, but this leads to a division conditions deterioration on the last separating switch points of long cuts with the following after them short cuts. Reducing the cuts rolling speed at the beginning of the sorting siding can be carried out using the beam on a stationary wagon retarders park brake position. Control Algorithm park brake position is quite simple. All produce should be unhooked from it at a safe speed. If the accuracy of the implementation of the set speed output to unhook from the park brake position is low, it is possible to eliminate the error of point regulators cars speed. Originality. The question where to start location point of wagon retarders zone to reduce speed to cut level requires additional research. Reducing rolling cut the speed at the beginning of the sorting sidings can be carried out using the beam on a stationary wagon retarders park brake position. Practical value. Control Algorithm park brake position is quite simple. All produce should be cut from it at a safe speed. If the accuracy of the implementation of the set speed output to cut from the park brake position is low, it is possible to eliminate the error of point regulators cars speed.
References
Bobrovskiy V.I., Kolesnik A.I. Analiz vliyaniya parametrov prodolnogo profilya sortirovochnoy gorki na dinamiku skatyvaniya ottsepov [Analysis of the effect of the parameters of longitudinal profile hump on the dynamics of rolling unhook]. Zbirnyk naukovykh prats Dnipropetrovskoho natsionalnoho universytetu zaliznychnoho transportu imeni akademika V. Lazariana «Transportnі sistemi ta tekhnologії perevezen» [Proc. «Transport systems and transportation technologies»], 2012, issue 3, pp. 10-14.
Bobrovskyi V.I., Dorosh A.S. Rehuliuvannia shvydkosti skochuvannia vidchepiv na avtomatyzovanykh sortuvalnykh hirkakh [Rolling-down speed control of cuts on automated humps ]. Tezy dopovidei 77-yi mizhnarodnoi naukovo-praktychnoi konferentsii «Rozvytok naukovoi ta innovatsiinoi diialnosti na transporti» (21.04-23.04.2015) [Proc. of 77th Int. Sci. and Practical. Conf. «Development of Scientisic and innovative activity at transport»]. Kharkiv, 2015, pp. 281-282.
Kozachenko D.M. Doslidzhennia dopustymykh rezhymiv halmuvannia vidchepiv na sortuvalnykh hirkakh [Research of permissible braking modes of cuts on humps]. Vostochno-Yevropeyskiy zhurnal peredovykh tekhnologiy – East Europian Journal of Advaced Technologies, 2013, no. 3 (64), vol 4, pp. 25-28.
Nazarov A.A. Analiz vozmozhnosti primeneniya sistem kvazinepreryvnogo regulirovaniya skorosti ottsepov tipa DOWTY na sortirovochnykh gorkakh [Application possibility analysis of systems of quasi-continuous speed control of cuts, type DOWTY on humps]. Zbirnyk naukovykh prats Kyivskoho univiversytetu ekonomiky i tekhnolohii transportu. Seriia «Transportni systemy i tekhnolohii» [Proc. of Kyiv University of Economy and Transport Technology. Series «Transport systems and transportation technologies»]. Kyiv, 2004, issue 4, pp. 61-66.
Nazarov O.A. Efektyvnist system rozpodilenoho rehuliuvannia shvydkosti vahoniv na sortuvalnykh koliiakh [The effectiveness of the systems of distributed control the speed of the car at the sorting path]. Visnyk Dnipropetrovskoho natsionalnoho universytetu zaliznychnoho transportu imeni akademika V. Lazariana [Bulletin of Dnipropetrovsk National University of Railway Transport named after Academician V. Lazaryan], 2010, issue 34, pp. 193-198.
Nazarov A.A. Opredeleniye ratsionalnogo sootnosheniya mezhdu uklonom sortirovochnogo puti i plotnostyu rasstanovki tochechnykh regulyatorov skorosti ottsepov [Determination of rational betweenness by slope of sorting siding and dencity of placing of point cut speed regulators]. Zbirnyk naukovykh prats Dnipropetrovskoho natsionalnoho universytetu zaliznychnoho transportu imeni akademika V. Lazariana «Transportnі sistemi ta tekhnologії perevezen» [Proc. «Transport systems and transportation technologies»], 2012, issue 3, pp. 77-80.
Ohar O.M., Taratushka K.V. Doslidzhennia efektyvnosti zastosuvannia tekhnolohii hravitatsiino-prytsilnoho hal-muvannia vidchepiv [Research of efficiency of application of technology of gravitational-targeted inhibition of cuts]. Zbirnyk naukovykh prats Dnipropetrovskoho natsionalnoho universytetu zaliznychnoho transportu imeni akademika V. Lazariana «Transportnі sistemi ta tekhnologії perevezen» [Proc. «Transport systems and transportation technologies»], 2015, issue 9, pp. 49-56. doi: 10.15802/tstt2015/49354
Zhang C., Wei Y., Xiao G., Wang Z., Fu J. Analysis of Hump Automation in China . Traffic and Transportation Studies, 2000, pp . 285–290. doi: 10.1061/40503(277)45
Dorosh A.S. Determination of Braking Optimal Mode of Controlled Cut of Design Group. Nauka ta prohres transportu – Science and Transport Progress, 2015, no. 3 (57), pp. 3644. doi: 10.15802/stp2015/46044.
Dreyer A.I., Marais J.S.F., Steyn H.J. Sentrarand Marshalling Yard: the mechanical engineering involvement. Die siviele ingenieur in Suid-Afrika, 1982, November, pp. 608-611, 613-614.
Lanchin W., Santos M.M., Lugli A.B. Speed Control and Braking System Automation of Wagon Parking System. Industry Applications (Induscon): 11th IEEE/IAS Intern. Conf. (7.12–10.12.2014). Juiz de Fora, 2014, pp. 1-6. doi: 10.1109/INDUSCON.2014.7059395.
Bobrovskyi V., Kozachenko D., Dorosh A., Demchenko E., Bolvanovska T., Kolesnik A. Probabilistic Approach for the Determination of Cuts Permissible Braking Modes on the Gravity Humps. Transport problems – Problemy transportu, 2016, vol. 11, issue 1, pp. 147-155. doi: 10.20858/tp.2016.11.1.14.
Zhang C., Li Y. Analys is of Over-speed Coupling Accidents on Hump based on Fuzzy Petri Net. Industrial Engineering and Engineering Management (IE&EM): 17Th Intern. Conference on (29.10-31.10.2010). Xiamen, IEEE, 2010, pp. 1014-1018. doi: 10.1109/ICIEEM.2010.5646453.
Downloads
Published
How to Cite
Issue
Section
License
Copyright and Licensing
This journal provides open access to all of its content.
As such, copyright for articles published in this journal is retained by the authors, under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0). The CC BY license permits commercial and non-commercial reuse. Such access is associated with increased readership and increased citation of an author's work. For more information on this approach, see the Public Knowledge Project, the Directory of Open Access Journals, or the Budapest Open Access Initiative.
The CC BY 4.0 license allows users to copy, distribute and adapt the work in any way, provided that they properly point to the author. Therefore, the editorial board of the journal does not prevent from placing published materials in third-party repositories. In order to protect manuscripts from misappropriation by unscrupulous authors, reference should be made to the original version of the work.
