RESEARCH OF THE STRESS STATE OF A MODIFIED IN-SITU CONCRETE

Authors

DOI:

https://doi.org/10.15802/stp2016/90515

Keywords:

modified concrete, in-situ concrete, stress state, deformation characteristics

Abstract

Purpose. The article focuses on investigation of the stress state of a modified in-situ concrete of natural hardening. Methodology. To achieve the aim, the research of the microstructure of the modified cement matrix of concrete, as well as the mechanism of structure formation of modified concrete with natural hardening was conducted; the methods for reliable evaluation of concrete strength were defined. Findings. The development of internal stresses affects the properties of concretedifferently. With an increase in temperature-shrinkage deformations in time and, thus, with increasing structural stresses in the cement sheath around the grains of the filler two opposite processes may develop: zone of plastic flow or cracking. Originality. It was established that the structural features complex of the modified concrete when the load transfer leads to the formation of extensive zones of prefracture which is able to absorb a significant amount of elastic strain energy that provides the design deformation properties of the concrete for special purposes. Ideas about the definition of the criteria of cracking modified concrete, hardening under natural conditions had further development. Practical value. The resulting equations allow to solve the problem about the minimum level of structural stress in monolithic concrete in a saturated large placeholder, as well as to assess the influence of structural stresses on the properties of concrete. In normal concrete with a relatively thin cement sheath at temperature-shrinkage deformations, high tangential and low radial tension occur. In vivo, this stress is higher as a result of higher values of Δε(τ), which is not observed in the modified concrete. In the modified concretes only tangential stresses are the greatest danger to structures. The change of shrinkage stress with time is straightforward. The total temperature-shrinkage deformations have a sawtooth graph. For modified concrete the amplitude is 48…53% less. This will allow solving a number of technological challenges in the construction of monolithic buildings.

Author Biography

D. V. Rudenko, Zaporizhzhia State Engineering Academy

Dep.«Urban Сonstruction and Management», Lenin Av., 226, Zaporizhzhia, Ukraine, 69006, tel. +38 (098) 214 04 85

References

Bazhenov, Y. M., Demyanova, V. S., & Kalashnikov, V. I. (2006). Modifitsirovannyye vysokokachestvennyye betony. Moscow: ASV.

Berg, O. Y. (1981). Fizicheskiye osnovy teorii prochnosti betona. Moscow: Stroyizdat.

Gansen, T. (1980). Polzuchest i relaksatsiya napryazheniy v betone. Moscow: Stroyizdat.

Nilssen, L. D. (1989). Udarnoye nagruzheniye betonnykh konstruktsiy. Moscow.

Piradov, K. A., & Guzeyev, Y. A. (1998). Mekhanika razrusheniya zhelezobetona. Moscow: Novyy vek.

Rabinovich, F. N. (2004). Kompozity na osnove dispersnoarmirovannykh betonov. Voprosy teorii i proyektirovaniya, tekhnologiya, konstruktsii. Moscow: ASV.

Rudenko, D. V. (2016). Beton na osnovi dyspersno modyfikovanoi tsementnoi systemy. Nauka ta prohres transportu – Science and Transport Progress, 4(64), 169-175. doi:10.15802/stp2016/78008

Rudenko, D. V. (2015). Fizyko-khimichna modyfikatsiia tsementnoi systemy monolitnoho betonu. Nauka ta prohres transportu – Science and Transport Progress, 6(60), 174-182. doi:10.15802/stp2015/57103

Rudenko, D. V. (2016). Tekhnolohiia modyfikovanykh betoniv dlia monolitnykh sporud. Paper presented at VI Mizhnarodna naukovo-praktychna konferentsiya «Efektyvni orhanizatsiino-tekhnolohichni rishennia ta enerhozberihaiuchi tekhnolohii v budivnytstvi», Kharkiv.

Rudenko, D. V. (2016). Modyfikovani betony dlia vysotnykh sporud. Paper presented at Mizhnarodna naukovo-praktychna konferentsiya «Efektyvni tekhnolohii v budivnytstvi», Kyiv.

Kherdtl, R., Ditermann, M., & Shmidt, K. (2011). Dolgovechnost betonov na osnove mnogokomponentnykh tsementov. Tsement i yego primeneniye – Cement and its Applications, 1, 76-80.

Collepardi, M. (2003). Innovative Concretes for Civil Engineering Structures: SCC, HPC and RPC. Paper presented at Workshop on New Technologies and Materials in Civil Engineering.

Derucher, K. M. (2009). Composite materials: Testing and Design. New Orleans-Philadelphia.

Hanehara, S., & Yamada, K. (2008). Rheology and early age properties of cement systems. Cement and Concrete Research, 38(l), 175-195. doi:10.1016/j.cemconres.2007.09.006

Lee, C. Y., Lee, H. K., & Lee, K. M. (2003). Strength and microstructural characteristics of chemically activated fly ash-cement systems. Cement and Concrete Research, 33(3), 425-431. doi:10.1016/S0008-8846(02)00973-0

Hsu, T. T. C., Slate, F. O., Sturman, G., & Winter, G. (1963). Microcracking of Plain Concrete and the Shape of the Stress Strain Curve. Intern. Concrete Abstracts Portal, 60(2), 209-224. doi:10.14359/7852

Middendorf, B., & Singh, N. B. (2006). Nanoscience and nanotechnology in cementitious materials. Cement International, 4, 80-86.

Neville, A. M. (2000). Wlasciwosci betonu. Crakow: Polski Cement.

Rudenko, D. (2013). Properties of the phase components of the modified cement system. Teka Komisji Motoryzacji i Energetyki Rolnictwa, 13(4), 218-224.

Rudenko, N. (2010). The Development of Conception of New Generation Concretes. Teka Komisji Motoryzacji i Energetyki Rolnictwa, 10B, 128-133.

Rudenko, N. (2014). Technology of shotcreting based on activated binder. Teka Komisji Motoryzacji i Energetyki Rolnictwa, 14(1), 222-228.

Santiago, S. D., & Hilsdorf, H. K. (1973). Fracture Mechanism of Concrete under Compressive Loads. Cement and Concrete Research, 3(4), 363-388. doi:10.1016/0008-8846(73)90076-8

Willis, J. R. (1982). Elasticity theory of composites. Mechanics of Solids, The Rodney Hill 60th Anniversary Volume, 653-686. doi:10.1016/B978-0-08-025443-2.50025-2

Published

2016-12-25

How to Cite

Rudenko, D. V. (2016). RESEARCH OF THE STRESS STATE OF A MODIFIED IN-SITU CONCRETE. Science and Transport Progress, (6(66), 166–174. https://doi.org/10.15802/stp2016/90515

Issue

Section

TRANSPORT CONSTRUCTION