CHOICE OF THE OPTIMAL PARAMETERS OF MEASURING THE SHAFT ROTATION FREQUENCY OF THE HYDRAULIC TRANSMISSION OF THE LOCOMOTIVE USING MICROCONTROLLER

Authors

DOI:

https://doi.org/10.15802/stp2017/99945

Keywords:

tachometer sensor, 2MMU-D-2, hydraulic transmission, hydraulic transmission test, testbench, information-measuring system

Abstract

Purpose. The article provides for finding solution to the problem of developing and improving the means for measuring tachometric data of the previously created information and measuring system for testing hydraulic locomotive transmission by substantiating the optimal sensor design and signal processing algorithms. At the same time first of all it is necessary to start from the possibility of modifying the already existing test bench for hydraulic locomotive transmissions at the Dnipropetrovsk diesel locomotive repair plant «Promteplovoz». Methodology. In the work, the researchers proposed a methodology for modifying the sensor design and the algorithm for processing its signals. It is grounded on previous developments of tachometric sensor of the optical type on the basis of D-2MMU-2 sensor of the microprocessor automated test bench system of hydraulic locomotive transmission in the locomotive repair plant conditions. Selection of the necessary measurement algorithm and the number of sensor teeth is substantiated by calculating instrumental and methodological errors. Also, the studies aimed at identifying the source of interference in the measurement of rotational speed are described and solution for its elimination has been found. Findings. For the designed rotation speed sensor of the optical type based on the existing D-2MMU-2 sensor, the authors analyzed the dependence of the methodological and instrumental errors. Based on the obtained data more rational variant of the rotation speed calculation algorithm is proposed, and the number of teeth of the sensor disk is justified. Further, the main source of measurement interference was established and a method for improving the hardware of the hydraulic locomotive test bench was proposed. Originality. There were conducted the studies according to the methodological and instrumental errors of the designed rotation speed of sensor. The mechanisms of interference filtering arising from the sensor rotation speed fixing were proposed. Additional studies have shown the need for a hardware revision of signal conditioner scheme. Practical value. Conducted studies make it possible to establish a rational number of sensor disk teeth, which allows improving the measurement algorithm. It was also performed a hardware improvement of signal conditioner scheme from the sensor, helping to get rid of interferences. The results of measurements in studies are the initial data to perform further studies in order to determine the technical condition of hydraulic transmission UGP 750-1200 during factory testing after repair.

Author Biographies

I. V. Zhukovytskyy, Dnipropetrovsk National University of Railway Transport named after Academician V. Lazaryan

Dep. «Electronic Computing Machines», Lazaryan St., 2, Dnipro, Ukraine, 49010,
tel. +38 (056) 373 15 89

I. A. Kliushnyk, Dnipropetrovsk National University of Railway Transport named after Academician V. Lazaryan

Dep. «Electronic Computing Machines», Lazaryan St., 2, Dnipro, Ukraine, 49010, 
tel. +38 (056) 373 15 89

References

Voskoboynikov, Y. Y., Gochakov, A. V., & Kolker, A. B. (2010). Filtratsii signalov i izobrazheniy: Fure i veyvlet algoritmy (s primerami v Mathcad). Novosibirsk: NSUACE.

Zhukovytskyi, I. V., & Kliushnyk, I. A. (2016). Vdoskonalennia metodiv ta zasobiv vymiriuvannia chastoty obertannia vala hidravlichnoi peredachi teplovoza z vykorystanniam mikrokontrolera. Proceedings of the X International Conference «Modern Information and Communication Technologies on a Transport, in Industry and Education», Dec. 14-15, 2016, Dnipro, Ukraine. 46-47.

Mamiy, A. R., & Tlyachev, V. B. (2005). Operatsionnyye usiliteli. Maikop: ASU.

Rabinovich, S. G. (1978). Pogreshnosti izmereniy. Leningrad: Energiya.

Sergienko, A. B. (2007). Tsifrovaya obrabotka signalov (2nd ed.). St. Petersburg: Piter.

Takhometry magnitoinduktsionnyye distantsionnyye TMi. (n.d.) Retrieved from http://sibspz.ru/pribory-dlya-izmereniya-parametrov-dvizheniya-takhometry/takhometry-magnitoinduktsionnye-distantsionnye-tmi

Carter, B. (2003). Op Amps for Everyone (2nd ed.). Texas, USA: Elsevier Science.

CD40106BM/CD40106BC. Hex Schmitt Trigger. (2011). Dallas, Texas: Texas Instruments Incorporated. Literature Number: SNOS353B. Retrieved from http://www.ti.com/lit/ds/symlink/cd40106bm.pdf

Zhukovytskyy, I. V., Kliushnyk, I. A., Ochkasov, O. B., & Korenyuk, R. O. (2015). Information-Measuring Test System of Diesel Locomotive Hydraulic Transmissions. Science and Transport Progress, 5(59), 53-65. doi: 10.15802/stp2015/53159

LMx24-N, LM2902-N. Low-Power, Quad-Operational Amplifiers. (2016). Dallas, Texas: Texas Instruments Incorporated. Retrieved from http://www.ti.com/lit/ds/symlink/lm2902-n.pdf

Merry, R. J. E., Van de Molengraft, M. J. G., & Steinbuch, M. (2013). Optimal higher-order encoder time-stamping. Mechatronics, 23(5), 481-490. doi: 10.1016/j.mechatronics.2012.10.011

Zhang, L., Slaets, Р., & Bruyninckx, Н. (2012). An open embedded hardware and software architecture applied to industrial robot control. Proceedings of the IEEE International Conference on Mechatronics and Automation, Aug. 5-8, 2012. 1822-1828. doi: 10.1109/ICMA.2012.6285098

Zhukovytskyy, I. V., & Kliushnyk, I. A. (2016). Use of microcontroller for measuring shaft speed of diesel locomotive hydraulic transmission. Science and Transport Progress, 5(65), 43-53. doi 10.15802/stp2016/83990

Downloads

Published

2017-04-24

How to Cite

Zhukovytskyy, I. V., & Kliushnyk, I. A. (2017). CHOICE OF THE OPTIMAL PARAMETERS OF MEASURING THE SHAFT ROTATION FREQUENCY OF THE HYDRAULIC TRANSMISSION OF THE LOCOMOTIVE USING MICROCONTROLLER. Science and Transport Progress, (2(68), 36–45. https://doi.org/10.15802/stp2017/99945

Issue

No. 2(68) (2017)

Section

OPERATION AND REPAIR OF TRANSPORT MEANS

License

Copyright and Licensing

This journal provides open access to all of its content.
As such, copyright for articles published in this journal is retained by the authors, under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0). The CC BY license permits commercial and non-commercial reuse. Such access is associated with increased readership and increased citation of an author's work. For more information on this approach, see the Public Knowledge Project, the Directory of Open Access Journals, or the Budapest Open Access Initiative.

The CC BY 4.0 license allows users to copy, distribute and adapt the work in any way, provided that they properly point to the author. Therefore, the editorial board of the journal does not prevent from placing published materials in third-party repositories. In order to protect manuscripts from misappropriation by unscrupulous authors, reference should be made to the original version of the work.